Indesit CI 56M W Instrucciones de uso descargar pdf (Pagina 28)

- 29 -

Check that the hose fits firmly into place at the two ends and fix it with clamps complying with current standards. If any of

the above recommendations can not be followed, flexible metal pipes should be used. If the cooker is installed in compliance

with the requirements for class 2, subclass 1, it is highly recommended that the gas connection be made with a flexible

metal pipe in compliance with current safety standards.

Connecting a FConnecting a F

Connecting a F

lele

xibxib

xib

lele

J J

ointlessointless

ointless

Stainless Steel Pipe to a Stainless Steel Pipe to a

Stainless Steel Pipe to a

hrhr

eaded eaded

eaded

AttacAttac

Attac

hmenthment

hment

Remove the hose holder fitted on the appliance. The gas supply pipe fitting is a threaded 1/2 gas cylindrical male attachment.

Use only pipes and seals that comply with current National Regulations. The full length of the pipe when installed must not

exceed 2000 mm. After the connection has been made, make sure that the flexible metal pipe does not come into contact

with moveable parts and that it is not crushed.

ChecChec

Chec

king the Sealking the Seal

king the Seal

Important: Once the installation has been completed, check to make sure that the seals on all the connections are tight,

using a soapy solution (never a flame).

Connecting the PConnecting the P

Connecting the P

er Suppler Suppl

er Suppl

y Cory Cor

y Cor

d to the Mainsd to the Mains

d to the Mains

Install a normalised plug corresponding to the load indicated on the data plate. When connecting the cable directly to the

mains, install an omnipolar circuit-breaker with a minimum contact opening of 3 mm between the appliance and the mains.

The omnipolar circuit breaker should be sized according to the load and should comply with current regulations (the earth

wire should not be interrupted by the circuit breaker). The supply cable should be positioned so that it does not reach a

temperature of more than 50°C with respect to the room temperature, along its length. Before making the connection,

check that:

• The limiter valve and the home system can support the appliance load (see data plate);

• The mains are properly earthed in compliance with current safety standards and regulations;

• There is easy access to the socket and omnipolar circuit breaker, once the hob has been installed.

N.B.: Never use reducers, adaptors or shunts since they can cause heating or burning.

ConCon

Con

erer

ting the Cookting the Cook

ting the Cook

er to Difer to Dif

er to Dif

erer

ent ent

ent

ypes ofypes of

ypes of

Gas Gas

Gas

In order to convert the cooker for use with a type of gas different than the one for which it was factory set (indicated on the

label attached to the lid), the following steps must be taken:

a) Replace the hose holder mounted on the appliance with that supplied in the bag of “cooker accessories.”

Important: The hose holder for liquid gas is marked 8, the hose holder for methane. In any case, always use a new

sealing gasket.

b) Replace the burner nozzles on the hob:

• Remove the grids and slide the burners from their housings;

• Unscrew the nozzles using a 7 mm socket spanner, and replace them with nozzles for the new type of gas (see

table 1 “Burner and Nozzle Characteristics”).

• Replace all the components by repeating the steps in reverse order.

c) Minimum regulation of the hob burners:

• Turn the tap to minimum;

• Remove the knob and adjust the regulation screw, which is positioned in or next to the tap pin, until the flame is small

but steady.

N.B.: In the case of liquid gas, the regulation screw must be screwed in all the way.

• Check that the flame does not go out when you turn the tap quickly from high to low.

d) Regulating the primary air of the burners: The primary air of the burners does not need to be regulated.

ImporImpor

Impor

tanttant

tant

On completion of this operation, replace the old rating sticker with one indicating the new type of gas used. This sticker is

available from our Service Centres.

NoteNote

Note

Should the pressure of the gas used be different (or vary) from the recommended pressure, it is necessary to fit a suitable

pressure regulator onto the inlet pipe in compliance with current National Regulations relative to “regulators for channelled

gas”.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 45 46

Comentarios a estos manuales

Sin comentarios

Indesit CI 56M W Instrucciones de uso Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Indesit CI 56M W