Indesit PC 640 N T X AUS Instrucciones de uso descargar pdf (Pagina 9)

Before connecting to the power supply, make sure that:

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these safety

measures not be observed.

Gas connection

Check The Gas Type

! Before installation, check that the gas type (natural gas

or LPG/Propane) of the cooker is suitable for the gas type

available to the installation. It is extremely dangerous to use

the wrong gas type with any appliance, as re or serious

injury can result.

This cooker is supplied from the factory already set for

Natural Gas. To convert the cooker to LPG (or back to

Natural Gas from LPG), follow the directions later in this

section.

Fit regulator supplied for Natural Gas (if applicable) at rear

of appliance, and as close as practicable to the appliance.

It is recommended that an isolating valve and union be

tted, to enable simple disconnection for servicing. These

are to be in an accessible location.

! Check that the pressure of the gas supply is consistent

with the values indicated in Table 1 (“Burner and nozzle

specications”). This will ensure the safe operation and

longevity of your appliance while maintaining efcient

energy consumption.

Pipe or Hose Connection

This appliance is suitable for use with either a exible

connection or rigid copper connection.

Either a rigid metal pipe with ttings in compliance with the

standards in force must be used for connecting to the nipple

union (threaded ½”G male tting) situated at the rear of the

appliance to the right (g.8), or an approved exible hose

of class B or D.

Should it be necessary to turn the fitting, the gasket

(supplied with the appliance) must be replaced.

If a exible hose is used, it should be as short as possible

with a maximum length of 1.5 metres;

• The exible connection must be approved to class B or

D of AS/NZS1869 as a minimum.

• it should not be bent, kinked or compressed;

• it should not be in contact with the rear wall of the

appliance or in any case with parts which may reach a

temperature of 50°C;

• it should not come into contact with pointed parts or sharp

corners;

• it should not be subject to any pulling or twisting forces;

• it should be easy to inspect along its entire length in order

to be able to check its condition.

• The supply connection point must be accessible with the

appliance installed.

• The inner diameters of the pipe are as follows:

8 mm for LPG;

13 mm for Natural Gas.

Checking the tightness of the connection

Upon completion of installation, check the gas circuit, the

internal connections and the taps for leaks using a soapy

solution (never a ame). Also check that the connecting pipe

cannot come into contact with moving parts which could

damage or crush it. Make sure that the natural gas pipe is

adequate for a sufcient supply to the appliance when all

the burners are lit

Duplicate Data Plate

Where the data plate is obscured by cabinetry when the

cooker is in the installed position, place a duplicate data

plate on a surface of the cabinetry adjacent to the cooker.

Adapting to different types of gas

To adapt the hob to a different type of gas other than default

type (indicated on the rating plate at the base of the hob or

on the packaging), the burner nozzles should be replaced

as follows:

1. Remove the hob grids and slide the burners off their

seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and

replace them with nozzles for the new type of gas (see

table 1 “Burner and nozzle characteristics”).

3. Reassemble the parts following the above procedure in

the reverse order.

4. Once this procedure is nished, replace the old rating

sticker with one indicating the new type of gas used.

Sticker are available from any of our Service Centres.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their

housing. The burner consists of two separate parts (see

pictures).

2. Unscrew the nozzles using a 7 mm socket spanner.

Replace the nozzles with models that are congured

for use with the new type of gas (see Table 1). The two

nozzles have the same hole diameter.

3. Replace all the components by completing the above

operations in reverse order.

AUS

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 31 32

Comentarios a estos manuales

Sin comentarios

Indesit PC 640 N T X AUS Instrucciones de uso Pagina 9

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Indesit PC 640 N T X AUS