Indesit PC 640 N T X AUS Instrucciones de uso descargar pdf (Pagina 8)

Pipe or Hose Connection

This appliance is suitable for use with either a exible connection or rigid

copper connection.

Either a rigid metal pipe with ttings in compliance with the standards in force

must be used for connecting to the nipple union (threaded ½”G male tting)

situated at the rear of the appliance to the right (g.8), or an approved exible

hose of class B or D.

Should it be necessary to turn the tting, the gasket (supplied with the

appliance) must be replaced.

If a exible hose is used, it should be as short as possible with a maximum

length of 1.2 metres;

• the exible connection must be approved to class B or D of AS/NZS1869

as a minimum.

• it should not be bent, kinked or compressed;

• it should not be in contact with the rear wall of the appliance or in any case

with parts which may reach a temperature of 50°C;

• it should not come into contact with pointed parts or sharp corners;

• it should not be subject to any pulling or twisting forces;

• it should be easy to inspect along its entire length in order to be able to

check its condition.

• The supply connection point must be accessible with the appliance

installed.

• The inner diameters of the pipe are as follows:

8 mm for LPG;

13 mm for Natural Gas.

Checking the tightness of the connection

Upon completion of installation, check the gas circuit, the internal connections

and the taps for leaks using a soapy solution (never a ame). Also check that

the connecting pipe cannot come into contact with moving parts which could

damage or crush it. Make sure that the natural gas pipe is adequate for a

sufcient supply to the appliance when all the burners are lit

Duplicate Data Plate

Where the data plate is obscured by cabinetry when the cooker is in the

installed position, place a duplicate data plate on a surface of the cabinetry

adjacent to the cooker.

Adapting to different types of gas

To adapt the hob to a different type of gas other than default type (indicated

on the rating plate at the base of the hob or on the packaging), the burner

nozzles should be replaced as follows:

1. Remove the hob grids and slide the burners off their seats.

2. Unscrew the nozzles using a 7 mm socket spanner, and replace them

with nozzles for the new type of gas (see table 1 “Burner and nozzle

characteristics”).

3. Reassemble the parts following the above procedure in the reverse order.

4. Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Sticker are available from any of our

Service Centres.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of their housing. The

burner consists of two separate parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner. Replace the nozzles

with models that are congured for use with the new type of gas (see Table

1). The two nozzles have the same hole diameter.

3. Replace all the components by completing the above operations in reverse

order.

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low ame position;

2. Remove the knob and adjust the adjustment

screw, which is positioned in or next to the tap

pin, until the ame is small but steady.

3. Having adjusted the ame to the required low setting, while the burner is

alight, quickly change the position of the knob from minimum to maximum

and vice versa several times, checking that the ame does not go out.

4. Some appliances have a safety device (thermocouple) tted. If the device

fails to work when the burners are set to the low ame setting, increase

this low ame setting using the adjusting screw.

5. Once the adjustment has been made, replace the seals on the by-passes

using sealing wax or a similar substance.

! If the appliance is connected to liquid gas, the regulation screw must be

fastened as tightly as possible.

! Once this procedure is nished, replace the old rating sticker with one

indicating the new type of gas used. Stickers are available from any of our

Service Centres.

! Should the gas pressure used be different (or vary slightly) from the

recommended pressure, a suitable pressure regulator must be tted to the

inlet pipe (in order to comply with current national regulations).

Post Installation Checks

Perform post installation checks and ensure proper and safe operation before

leaving. Test all burners individually and in combination.

Leak Check

• Ensure all gas control knobs are in the Off position.

• Ensure the gas supply is switched on.

• Spray a solution of soapy water onto all gas joints as well as the full length

of any exible hoses. UNDER NO CIRCUMSTANCES USE A NAKED

FLAME IN CHECKING FOR LEAKS.

If bubbles appear anywhere, turn the gas supply off, check all connections and

retest. If satisfactory operation cannot be achieved, contact place of purchase

or their appointed agent for service.

AUS

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 27 28

Comentarios a estos manuales

Sin comentarios

Indesit PC 640 N T X AUS Instrucciones de uso Pagina 8

Comentarios a estos manuales

Relacionado con productos y manuales para Placas Indesit PC 640 N T X AUS